EFFECT OF CU AS МINORITY АLLOYING ЕLEMENT ON GLASS FORMING ABILITY AND CRYSTALLIZATION BEHAVIOR OF RAPIDLY SOLIDIFIED AL-SI-NI RIBBONS

Authors

  • Vanya Dyakova IMSETHAC-BAS, Materials Testing and Analyses (BG)
  • Hristina Spasova IMSETHAC-BAS, Materials Testing and Analyses (BG)
  • Yoanna Kostova IMSETHAC-BAS, Materials Testing and Analyses (BG)
  • Yana Mourdjeva IMSETHAC-BAS, Materials Testing and Analyses (BG)
  • Georgi Stefanov IMSETHAC-BAS, Metal science (BG)

DOI:

https://doi.org/10.17770/etr2023vol3.7200

Keywords:

amorphous, nanocrystalline, aluminum, copper, silicon, nickel

Abstract

The influence of copper as a minority alloying element in the process of rapid solidification of Al-Si-Ni ribbons produced by Chill Block Melt Spinning (CBMS) was investigated. XRD and TEM analyses proved a completely amorphous structure of the alloys Al74Ni16Si10 and (Al74Ni16Si10)98Cu2. The crystallization behaviour of these alloys was studied by DSC analysis. It was found that the crystallization of the amorphous alloys (Al74Ni16Si10)100-xCux, x=0, 2 runs in two steps. The temperatures Tx1 and Tx2 of each of the crystallization steps were determined. It was proven that the addition of 2 at. % copper does not significantly change Tx temperatures. The temperature difference ΔTx was calculated and it showed that more thermally stable is the copper containing alloy. Crystalline analogues of the amorphous alloys were obtained by annealing of the melt-spun amorphous ribbons at a temperature which exceeded by 170°C the onset crystallization temperature. The type and size of separated crystalline phases were determined by XRD. It was found that the addition of 2 at. % Cu to Al74Ni16Si10 alloy causes a separation of new phases - Cu3.8Ni and (Al, Cu)Ni3 and 54%, 24% and 7% size increase of the phases Al, Al3Ni, NiSi2 respectively.

Supporting Agencies
This study is funded by the project “Study of the rheological and corrosion behavior of amorphous and nanocrystalline aluminum-based alloys”, Contract with BNSF №KP-06-H37/13 of 06 December 2019. A part of experimental units used in this work was funded by the European Regional Development Fund within the OP “Science and Education for Smart Growth 2014 - 2020”, project CoE “National center of mechatronics and clean technologies”, No BG05M2OP001-1.001-0008-C08. The authors are indebted to our colleagues prof. Stoyko Gyurov, PhD, Jordan Georgiev, Ivan Penkov, PhD (IMSETHAC-BAS) and prof. Daniela Kovacheva, ass. prof. Nikolay Marinkov, PhD (IIC – BAS) for their help and support in the preparation and for the XRD and DSC analyzes of the alloys.

Downloads

Download data is not yet available.

References

Y. H. Kim., K. Hiraga, A. Inoue, T. Masumoto , H. H. Jo, “Crystallization and Hight Mechanical Strength of Al-Based Amorphous Alloys” Materials Transactions, JIM, vol. 35, pp. 293-302, 1994, https://doi.org/10.2320/matertrans1989.35.293

H. Kim, A. Inoue and T. Masumoto, “High Strength Bulk Amorphous Alloys with Low Critical Cooling Rates (Overview)”, Material Transactions, JIM, vol. 36, , no. 7, pp.866-875,1995 https://doi.org/10.2320/matertrans1989.36.866

I. T. H Chang, R. R Botten, “Heat treatment of rapidly solidified Al-Ni-Mm alloys”, Materials Science and Engineering: A, vol. 226-228, pp.183-186, 1997 https://doi.org/10.1016/S0921-5093(97)80035-4

W. Kim, M. Gogebakan, B. Cantor, “Heat treatment of amorphous Al85Y5Ni10 and Al85Y10Ni5 alloys”, Materials Science and Engineering: A”, vol. 226–228, , pp.178-182, 1997 https://doi.org/10.1016/S0921-5093(96)10613-4

I. Permyakova, A. Glezer, “Amorphous-Nanocrystalline Composites Prepared by High-Pressure Torsion”, Metals, vol.10, no. 4, p.511, 2020 https://doi.org/10.3390/met10040511

A. H. Brothers, D. C. Dunand, “Amorphous metal foams”, Scripta Materialia, vol. 54, no. 4, , pp. 513-520, 2006 https://doi.org/10.1016/j.scriptamat.2005.10.048

M. Gögebakan, O. Uzun, T. Karaaslan, M. Keskin, “Rapidly solidified Al–6.5 wt. % Ni alloy”, Journal of Materials Processing Technology, vol. 142, no.1, pp. 87-92, 2003, https://www.sciencedirect.com/science/article/abs/pii/S0924013603004667

M. A. Munoz-Morris, S. Surinach, M. Gich, M. D. Baro, D. G. Morris, “Crystallization of a Al–4Ni–6Ce glass and its influence on mechanical properties”, Acta Materialia, 51, , pp. 1067-1077, 2003 https://doi.org/10.1016/S1359-6454(02)00511-6

A. K. Gangopadhyay, K. F. Kelton, “Effect of rare-earth atomic radius on the devitrification of Al88RE8Ni4 amorphous alloys”, Philosophical Magazine A, vol. 80, , pp. 1193-1206, 2000 https://doi.org/10.1080/01418610008212110

N. Bassim, C.S. Kiminami, M. J. Kaufman, M. F. Oliveira, M.N.R.V.Perdigão, W.J. Botta Filho, “Crystallization behavior of amorphous Al84Y9Ni5Co2alloy”, Materials Science and Engineering A, 304–306, pp.332-237, 2001 https://doi.org/10.1016/S0921-5093(00)01532-X

T. Gloriant, D.H. Ping, K. Hono, A. L. Greer, M.D. Baro, “Segregation-controllednanocristalization in an Al-Ni-La metallic glass”, Applied Physics Letters, 92, 103126, 2008, https://doi.org/10.1063/1.2897303

V. Dyakova, G. Stefanov, I. Penkov, D. Kovacheva, N. Marinkov, Y. Mourdjeva, S. Gyurov, “Influence of Zn on Glass Forming Ability and Crystallization Behaviour of Rapidly Solidified Al-Cu-Mg (Zn) alloys”, Journal of Chemical Technology and Metallurgy, 57, 6, pp. 622-630, 2020 https://journal.uctm.edu/node/j2022-3/23_21-64_br_3_pp_622-630.pdf

V. L. Dyakova, G. N. Stefanov, D. G. Kovacheva, Y. S. Mourdjeva, N. E. Marinkov, .I. G. Penkov and J. S. Georgiev, Influence of Zr and Zn as minority alloying elements on glass forming ability and crystallization behavior of rapidly solidified AlCuMg ribbons, 2449, AIP Conference proceedings, 2022, https://aip.scitation.org/doi/abs/10.1063/5.0090746

V. L. Dyakova, B. R. Tzaneva and Y. G. Kostova, “Influence of Zn as minority alloying element on the uniform and local corrosion of amorphous rapidly solidified AlCuMg(Zn) ribbons”, 2449, AIP Conference proceedings, 2022, https://doi.org/10.1063/5.0090752

R. Birringer, H. Gleiter, P. Klein, P. Marquardt, “Nanocrystalline materials an approach to a novel solid structure with gas-like disorder?”, Physics Letters A, vol.102, no.8, pp. 365-369, 1984 https://doi.org/10.1016/0375-9601(84)90300-1

M. Gögebakan, M. Okumus, Structure and crystallization kinetics of amorphous Al–Ni–Si alloy, Materials Science-Poland, vol. 27, no. 1, 2009, https://materialsscience.pwr.edu.pl/

K.L. Sahoo, R. Sahu, “Glass transition and crystallization of Al–Ni–La based metallic glasses studied by temperature modulated DSC”, Journal of Non-Crystalline Solids, 365, , pp. 33-36, 2013 http://dx.doi.org/10.1016/j.jnoncrysol.2013.01.031

Downloads

Published

2024-01-16

Issue

Vol. 3 (2023): Environment. Technology. Resources. Proceedings of the 14th International Scientific and Practical Conference. Volume 3

Section

Engineering Sciences and Production Technologies

How to Cite

[1]
V. Dyakova, H. Spasova, Y. Kostova, Y. Mourdjeva, and G. Stefanov, “EFFECT OF CU AS МINORITY АLLOYING ЕLEMENT ON GLASS FORMING ABILITY AND CRYSTALLIZATION BEHAVIOR OF RAPIDLY SOLIDIFIED AL-SI-NI RIBBONS”, ETR, vol. 3, pp. 69–73, Jan. 2024, doi: 10.17770/etr2023vol3.7200.