MODELLING AND SIMULATION OF DYNAMIC PROCESSES OF PNEUMATIC LINES
DOI:
https://doi.org/10.17770/etr2023vol3.7190Keywords:
pneumatic line, simulation, mathematical model, experimentsAbstract
The paper presents the simulation of dynamic processes of pneumatic lines using the program "SIMULINK" from the product " MatLab". Simulation is a process of forming, preparing and entering a mathematical model in a computational environment and obtaining the results of the calculations performed in this environment. The mathematical model of the pneumatic line to be simulated is according to previously presented equations. For the simulation of the dynamic processes, various real parameters of the dimensions and lengths of the pneumatic lines with the corresponding coefficients are introduced into the model. The simulation of the transient responses was carried out with stepwise variation and sinusoidal input signal supplied by the set point device and pneumatic line lengths of 1 m, 5 m and 10 m. The simulation output data were output to the interface in the form of graphs showing the dependence of the observed quantities, the input and output pressure through the pneumatic line, and the input and output flow rates. From the mathematical model and the experiments performed, it can be concluded that the transient responses in the simulations correspond to the dynamic processes of pneumatic lines of different lengths.
Downloads
References
Andreev, A., H. Hristov, G. Iliev, M. Racheva.”Mathematical model for a Pneumatic force Actuator System” Journal of the Technical University of Gabrovo, Bulgaria Vol. 53’2016
Hristov, H., K. Ormanjiev, P. Ivanov, "Investigation of the transient processes of an electro-pneumatic drive system with a hydraulic speed stabilizer" Journal of Mechanics of Machines No62, Series FH: APPLIED MECHANICS OF FLUIDS HEAT AND MASS TRANSFER, Year XIV, Book 1, Technical University of Varna Press, Bulgaria 2006
Iliev, G., A. Anchеv, H. Hristov, S. Rachev. “Stand for experimental study of dynamic processes in Electro- pneumatic tracking System” XXII International Conference “Eko- Ist| 2014. Bor, SERBIA (124-130)
Iliev, G., H. Hristov, A. Anchеv,"Experimental study of the static characteristics of a proportional directional control valve" Volume 3, pages 318-323, UNITECH'15, Gabrovo, Bulgaria 2015.
Kreinin, G., S. Misyurin, S.Nosova. “Parametric and Structural Optimization of Pneumatic Positioning Actuator”; pp.123-129. 2020.
Mihai, A., C. Bucsan, L. Bogat; “Pneumatic Incremental Proportional Valve Part of the Lecture Notes in Networks and Systems book series” (LNNS, volume 85 20 ) July 2019
Bavaresco, D., Mathematical modeling and control of a pneumatic actuator, M.S. thesis, Mathematical Modeling Master Course, UNIJUÍ - Regional University of Northwestern Rio Grande do Sul State, Brazil, 2007
Chiara, G., D. Prattichizzo, A Mathematical Model of the Pneumatic Force Sensor for Robot-assisted Surgery IEEE World Haptics Conference (WHC) pp.121-126. 2019
Richer E., Yildirim Hurmuzlu; A high performance pneumatic force actuator system: part 1—Nonlinear mathematical model: J. Dyn. Sys., Meas., Control. Sep 2000, 122(3): 416-425 (10 pages) https://doi.org/10.1115/1.1286336
Richer E., Yildirim Hurmuzlu; A High Performance Pneumatic Force Actuator System: Part II—Nonlinear Controller Design: J. Dyn. Sys., Meas., Control. Sep 2000, 122(3): 426-434 (9 pages) https://doi.org/10.1115/1.1286366
Andrzej Laski., Takosoglu Jakub Emanuel, Design of a 3-DOF tripod electro-pneumatic parallel manipulator, Robotics and Autonomous SystemsVolume 72, October 2015, Pages 59-70
Jarquin Laguna A., Tsouvalas A.: Transient laminar flow in hydraulic networks based on a semi-analytical impulse response method. HERON Vol. 59 (2014) No. 1 (2014).
Dihovicni D., M Medenica, Mathematical modelling and simulation of pneumati systems, Advances in computer science and engineering 2011pages (161-186)
Franco E.; M. Ristic Time delay controller for the position control of a MRI-compatible pneumatic actuation with long supply lines IEEE/ASME (AIM) International Conference on Advanced Intelligent Mechatronics 8-11 July 2014
Turkseven Melih, Jun Ueda, Model-Based Force Control of Pneumatic Actuators With Long Transmission Lines; IEEE/ASME Transactions on Mechatronics ( Volume: 23, Issue: 3, June 2018) Page(s): 1292 – 1302; 03 May 2018
