OPTIMIZATION OF BURNING PRODUCTION PROCESS OF CERAMSITE WITH SPECIFIED DENSITY
DOI:
https://doi.org/10.17770/etr2017vol3.2569Keywords:
claydite, rotary kiln, strength and bulk density of ceramsite, mathematical modelAbstract
The paper goes into peculiarities of using developed mathematical models of ceramsite burning and computational models created on their basis. The work is done in the light of analysis and synthesis of multivariate control system of kiln angular velocity and kiln charge with volumetric thermal capacity burners. It is shown that computational models of burning as an object of control are problem-oriented on producing ceramsite with specified density. Mathematical model of ceramsite burning process as an object with distributed parameters is synthesized. The transition from model with distributed parameters to the mode with lumped parameters is performed. Then the authors used a model with three bearing cross-sections along Z-axis in Matlab software and created a computational model of multivariate object of control with inter-channel connections. The paper presents experimental computational set up methods and methods of ceramsite burning optimal curve identification on the criterion of minimizing energy consumption for burning. The developed method of staging computational experiments makes it possible to predict the strength of ceramsite if values of control actions are known. The results of modeling help create methodology of choosing optimal modes of ceramsite burning with the required mark of strength and with minimum energy consumption.Downloads
References
Lisienko V.G., Shchelokov Ya.M., Ladygichev M.G. Rotary kilns: heat engineering, management and ecology, Book 1, Moscow, Heating engineer, 2004, 688 p.
Lisienko V.G., Shchelokov Ya.M., Ladygichev M.G. Rotary kilns: heat engineering, management and ecology, Book 2, Moscow, Heating engineer, 2004, 592 p.
Yıldız M., Soğanci A.S. Effect of freezing and thawing on strength and permeability of lime-stabilized clays. Scientia Iranica, Vol. 19, Is. 4, 2012, pp. 1013–1017.
Chuan Wang, n-Xin Chen, Chao Dang Yuan-Zhe Li, Aruna, Hai-Chao Li, Yu Huang Preparation of Ceramsite from C&D Waste and Baiyunebo Tailings. Procedia Environmental Sciences, Vol. 31, 2016, pp. 211–217.
Fan Tie-lin, Chen Mi-mi, Zhao Feng-qing The preparation of phase change energy storage ceramsite from
waste autoclaved aerated concrete. Procedia Environmental Sciences, Vol. 31, 2016, pp. 227–231.
Metin Davraza, Murat Korub, Ali Ekrem Akdağ. The Effect of Physical Properties on Thermal Conductivity of Lightweight Aggregate Procedia Earth and Planetary Science, Vol. 15, 2015, pp. 85–92.
Kartushina Yu. N., Shaikhiev I. G., Ananyev D. Waste treatment plants and charcoal production wastes as a corrective additive in the production of ceramsite. Vestnik of Kazan Technological University, Vol.17, Is.21, 2014, pp. 195-198.
Sokolov L.I., Fomenko A.I. Reclamation of Waste Products in Aglite Production. Industry ecology. Vol. 19, 9, 2015, pp. 30-34.
Kislenko Т.A., Koshkarev S.A., Sidyakin P.A., Eremyan S.P. The Basic Significance Of Parameters Of Inertial Devices Cleaning Ventilation Emissions In Claydite Manufacturing. Modern problems of science and education, 1, 2014.
Toropkov N.E. Influence of molding conditions clay matters for claydite and waste treatment methods of claydite production. Scientific Almanac, 8 (10), 2015, pp. 1039-1045.
Maksimova I.N., Makridin N.I. Technological Features Of Light Concretes Structure And Properties Formation. Regional architecture and engineering, 2, 2012, pp 45-48.
Castrodale R.W., Harmon, K.S. Increasing Design Efficiency Using Lightweight Concrete for Prestressed Girder Bridges. Paper 55, Proceedings, 2005 National Bridge Conference, Palm Springs, CA, PCI, October 16-19, 2005.
Castrodale R.W., Eriksson R.L., Barngrover B. Comparative Bridge Designs Using Normal Weight and Lightweight Concrete. Paper 45, Proceedings, 2009 National Bridge Conference, San Antonio, TX, PCI, September 13-15, 2009.
Vaiana R., Capiluppi G.F., Gallelli V., Iuele T., Minani V. Pavement Surface Performances Evolution: an Experimental Application. Procedia - Social and Behavioral Sciences, Vol. 53, 3 October, 2012, pp. 1149–1160.
Galitskov S.Ya., Galitskov K.S., Samohvalov O.V. Modelling Operating Area of Condition and Management of High Strength Bloating Clay, Stoving in a Rotary Kiln. Procedia Engineering, XXV R-S-P Seminar, Theoretical Foundation of Civil Engineering (25RSP), Vol. 111, 2016, рр. 233–235.
Galitskov S.Ja., Galitskov K.S., Samohvalov O.V., Fadeev A.S. Modeling the calcination of ceramsite in a rotary furnace with regulated speed as a control object. Science Review, 7, 2015, pp. 227-237.
Galitskov S. Y., Samokhvalov О. V., Fadeev А. S. Structural synthesis of a multi-dimensional system for automated control of claydite baking in a rotary furnace. Science Review, 12, 2013, pp. 204-208.
Galitskov К.S., Samohvalov О.V. Strength properties of expanded clay and their reflection in the range of various temperature modes of three supporting cross-sections of kiln. Promyshlennoe i grazh¬danskoe stroitelstvo [Industrial and Civil Engineering], 9, 2015, pp. 91—94.
Vorobyov V.A., Ilyukhin A.V., Kolbasin O.M., Popov V.P. Automating preparation of concrete mixtures and manufacturing of reinforced-concrete products and structures. Publishing House of the Russian Academy of engineering, 2016, 660 p.
Vorobyov V.A., Ilyukhin A.V., Kolbasin O.M., Popov V.P. Automating the production of concrete mixtures for road construction. Publishing House of the Russian Academy of engineering, 2014, 420 p.
Rapoport, E.Ya., Pleshivtseva Yu.E. Optimal control of thermal management of induction heating. Moscow, Science, 2012, 309 p.
