Factors influencing the color laser marking
DOI:
https://doi.org/10.17770/etr2015vol1.223Keywords:
laser, marking, color lettering of stainless steelAbstract
In recent years, conventional techniques of marking on some parts of different work pieces, as well as on packages with color printing are increasingly being displaced by laser color marking. Colored marking of stainless steel could be realized by the process annealing. The advantages offered by the new technology are in greater accuracy, speed, flexibility and high amount of recorded information per unit area (bar and matrix codes).
In the report are discussed and analyzed the factors influencing on the specific to the process of laser color marking at the products of CrNi steel. The study was conducted using a commercially available industrial pulsed fiber laser. Presents the results of the measurements and analysis of the influence of laser process parameters on the color contrasting obtained. In this case, the relevant parameter, the field of high frequencies and low pulse energy were examined. The present thesis describes studies a properties of the laser radiation, such as, pulse width, average power, the intensity and beam diameter.
Downloads
References
A. Pérez del Pino, P. Serra, J.L. Morenza, Oxidation of titanium through Nd_YAG laser irradiation. Appl. Surf. Sci. 197–198, 887–890 (2002)
S. O’Hana, A.J. Pinkerton, K. Shoba, A.W. Gale, L. Li, Laser surface colouring of titanium for contemporary jewelery. Surf. Eng. 24, 147–153 (2008)
Á. Perez del Pino, J.M. Fernandez-Pradas, P. Serra, J.L. Morenza, Coloring of titanium through laser oxidation: comparative study with anodizing. Surf. Coat. Technol. 187, 106–112 (2004)
Z.L. Li, H.Y. Zheng, K.M. Teh, Y.C. Liu, G.C. Lim, H.L. Seng, N.L. Yakovlev, Analysis of oxide formation induced by UV laser coloration of stainless steel. Appl. Surf. Sci. 256, 1731–1734 (2009)
A.J. Anto´nczak, D. Koco´n, M. Nowak, P. Kozioł, K.M. Abramski, Laser-induced colour marking—Sensitivity 16. L. Baufay, F.A. Houle, R.J.Wilson, Optical self-regulation during laser-induced oxidation of copper. J. Appl. Phys. 61, 4640 (1987)
S. Fujimoto, K. Tsujino, T. Shibata, Growth and properties of Cr-rich thick and porous oxide films on Type 304 stainless steel formed by square wave potential pulse polarisation. Electrochim. Acta 47, 543–551 (2001)
A.Y. Vorobyev, C. Guo, Colorizing metals with femtosecond laser pulses. Appl. Phys. Lett. 92, 041914 (2008)
E.B. Barmina, E. Stratakis, C. Fotakis, G.A. Shafeev, Generation of nanostructures on metals by laser ablation in liquids: new results. Quantum Electron. 40, 1012 (2010)
www.inoxstory.ru/ask.html]
Гост 5632-72, издательство стандартов, Москва, www.docload.ru/Basesdoc/3/3936/index.htm
Шахно Е. А. Аналитические методы исследования и разработки лазерных микро- и нанотехнологий. Методические рекомендации по выполнению курсовых проектов и само-стоятельных работ студентов. – СПб: СПбГУ ИТМО, 200818
Вейко В. П., Горный С. Г., Одинцова Г. В. и др. Формирование многоцветного изображения при лазерном окислении металлов. – Изв. вузов. Приборостроение, 2011, т.54, №2, c.47–53
