STUDY OF LASER CUTTING AND MARKING ON THE FILT WITH THE HELP OF A CO2-LASER

Authors

  • Lyubomir Lazov Rezekne Academy of Technologies, Latvia (LV)
  • Nikolay Todorov Dolchinkov National Military University „Vasil Levski“, Veliko Tarnovo, Bulgaria, National Research University "Moscow Power Engineering Institute", Moscow, Russia (BG)
  • Jordan Shterev Ivanov National Military University „Vasil Levski“, Veliko Tarnovo, Bulgaria (BG)
  • Madlen Nikolaeva Peneva National Military University „Vasil Levski“, Veliko Tarnovo, Bulgaria (BG)
  • Denitsa Angelova Bojhanova National Military University „Vasil Levski“, Veliko Tarnovo, Bulgaria (BG)

DOI:

https://doi.org/10.17770/etr2019vol3.4202

Keywords:

cutting, filt, laser, marking, research

Abstract

Describe the parameters influencing the depth of the laser marking of textile products. Experimental results are presented to determine the quality of cuts on felt surfaces of different colors at specific parameters - power and speed. Approximately 100 extras were made on two materials with a change in laser power and speed. As a result, the optimal results for cutting and marking a felt are shown.

 

Downloads

Download data is not yet available.

References

Dave Ahearn, ONR Laser Power Jumps 10 Fold; Further 10 - Fold Leaps Seen, Defense Today, August 4, 2004, p. 4

Dolchinkov N., Shterev Y., St. Lilianova, D. Boganova, M. Peneva, L. Linkov, D. Nedialkov, Exploring the possibility of laser cutting with CO2 laser on felt in the range from 1W to 26W power, International scientific journal: Industry 4.0 Issue 1/2019, ISBN 2534-8582, стр. 29-31.

Lamberson S. E., The airborne laser, Proc. SPIE, Gas Chem. Lasers, vol. 2702, pp. 2702-1_2 702 - 6, Mar. 1996

.Lazov L., E. Teirumnieks, Application of laser technology in the army, Proceedings of International Scientific Conference “Defense Technologies”, Faculty of Artillery, Air Defense and Communication and Information Systems, Shumen, Bulgaria, 2018

Lazov L,, H. Deneva, E. Teirumnieka, Influence of Defocus Position on Laser Cutting Process in Sheet Steel, Environment. Technology. Resources, Rezekne, Latvia Proceedings of the 11 th International Scientific and Practical Conference. Volume III, 163-167,

Lazov, L., H. Deneva. Investigation on the Influence of the Process Parameters Power and Velocity to Laser Cutting of Lamellae. Journal of the Technical University - Sofia, Plovdiv branch, Bulgaria, Fundamental Sciences and Applications, Vol. 21, Book 2, 2015, ISSN 1310-8271.

Lazov L., Аngelov N., Scanning the contrast in function of velocity in laser marking of samples of steel, International Scientific Conference, Gabrovo, 2010.

Petrov N., Optimization of the marking process with laser radiation of samples of tool steel, dissertation, Gabrovo, 2011.

Shterev Y., N. Dolchinkov, St. Lilianova, D. Boganova, M. Peneva, L. Linkov, D. Nedialkov, Еxamining the possibility Of marking and engraving of textiel using CO2 laser, International journal for science Machines, Technologies, Materials 12/2018 стр 491-493

https://www.laserfelt.com/

http://chris-reilly.org/blog/how-to-laser-cut-felt/

https://www.epiloglaser.com/resources/sample-club/felt-placemat-cutting.htm

https://www.lasercuttingshapes.com/felt/

https://www.pinterest.com/eleeneelab/laser-cut-felt/

http://digitalcommons.unl.edu/tsaconf/index.2.html

https://developer.paciellogroup.com/resources/contrastanalyser

https://rdworks.software.informer.com

Downloads

Published

2019-06-20

Issue

Vol. 3 (2019): Environment. Technology. Resources. Proceedings of the 12th International Scientific and Practical Conference. Volume 3

Section

Engineering Sciences and Production Technologies

How to Cite

[1]
L. Lazov, N. T. Dolchinkov, J. S. Ivanov, M. N. Peneva, and D. A. Bojhanova, “STUDY OF LASER CUTTING AND MARKING ON THE FILT WITH THE HELP OF A CO2-LASER”, ETR, vol. 3, pp. 143–147, Jun. 2019, doi: 10.17770/etr2019vol3.4202.